How to Install a Ghost Immobiliser
A ghost immobiliser guards your vehicle from key cloning or hacking. It prevents the engine from starting until a PIN code has been entered. This could be as long as 20 characters.
This additional layer of security is not visible to thieves who may not expect it. Some systems also have an application that allows owners to disarm the immobiliser in case they forget their PIN or to switch to a service/valet mode.
Connecting to the vehicle's CAN bus
The Ghost 2 Immobiliser is an advanced security system that can be incorporated into your vehicle's ECU offering a secure security line against thieves. It is extremely efficient and user-friendly and can be a valuable option to add to your vehicle's security arsenal. Like all anti-theft devices it's not foolproof, and requires regular maintenance to function properly. This guide will help you get the most of your Ghost 2 immobiliser.
CAN (Controller Area Network), a robust serial networking, allows microcontrollers communicate with each other over small distances. Central control units is not required. It is designed to allow multiplexing of electrical wiring in vehicles to cut down on copper and comes with a variety of advantages, including low cost and ease of use.
The CAN protocol is utilized in the majority of modern vehicles to communicate with the engine management system, steering control module, air conditioning controls, and many more. It also relays information from sensors, such as speed sensors and other inputs, to regulate the car's various features. The CAN bus can be used to monitor the health of these different components. It can prevent the vehicle from starting if it is in an unsafe condition.
Although the CAN bus can be used for a variety of purposes, it's important to understand how it works and how it's secured. It is possible to add new features to a vehicle by using CAN bus, but it's crucial to safeguard it from threats from hackers and other types. The best method to achieve this is to install firewalls and monitoring your CAN bus using software.
Ghost2's secluded control unit is hidden away in the wiring harness or dashboard, eliminating the possibility of a burglar physically altering it. It is also impossible to reset a pin code or an emergency code without access to the vehicle.
You can activate Transport Mode when you have to sell your car for valet parking, service or for any other reason. This feature will disable the Ghost immobiliser's ignition and keyfob functions, and will only reactivate when the vehicle is speeding at 31 mph for a period of 15 minutes.
How to create a PIN code
The Ghost immobiliser shields your vehicle from theft. The patented technology makes use of an PIN to shut down the engine of your vehicle and prevent it from starting if you don't have the correct code, or an authorized fob/mobile. Its discrete design ensures the system is inconspicuous and provides unrivaled protection against theft. Furthermore, car stolen with ghost immobiliser is TASSA certified and can lead to significant savings on insurance premiums for cars.
During the installation during installation, the Ghost system enters an learning mode that records the sequence of buttons pressed to generate your unique pin code. The installer will guide you through activating the system once the pin code has been created. Once activated, the Ghost system will turn off your vehicle's starter motor until a valid PIN has been entered or the vehicle is switched into transport mode. This makes it extremely difficult for thieves or cloners to hack or duplicate the starter system of your vehicle.
It is easy to install it is easy to install a Ghost immobiliser, however, you must follow the precise instructions provided in the user guide to ensure the proper operation. Basic hand tools will assist in making the perfect connections and a multimeter will assist in determining electrical values. Insulation tape and heat shrink tubing can shield the wire from damage Cable tie is essential to keep everything neat and secure. Also, be certain to test the system regularly to identify any problems and potential errors.
It is essential to check the system one final time prior to turning on the ignition. Ghost immobilisers will arm themselves after 3 to 30 second, dependent on the model of your vehicle. The system is also fitted with a Service/Valet mode that allows you to temporarily disable the system to service or valet parking.
Ideally, the immobiliser should be concealed in a hidden location beneath the dashboard or steering wheel. Use a small amount of tape or paint on the wires CAN H and L to make them easier to find when you are testing. Additionally the CAN H and CAN L wires must be connected to a power source that has constant 12V. It is also crucial to check the connections again after testing, as misidentifying these wires can cause the system to malfunction.
Invoking the system
A ghost immobiliser stops your car from starting unless you press a sequence of buttons inside the car, usually the steering wheel, door panel or central console. The sequence is set by the user and can be altered at any time. Once the system is activated, it is not able to be disabled by thieves and is a great option for anyone who wishes to protect their vehicle from theft.
The system is not designed to be detectable by modern diagnostics and code-grabbing technologies. It also does not send radio signals, which makes it even difficult for thieves to find the device.
If the device is found, it will stop the engine from starting. It will also sound an alarm to scare the burglar away. The device can be used to track a car's location, which will assist in the recovery of the vehicle in case it has been stolen.
Contact Car Specalist Customs for a quote or to discuss your options in an immobiliser that is ghost-like. We are able to install ghost immobilisers on your vehicle. We will make sure that it is hidden in a place that is difficult to reach. We can also provide additional security measures, such as a wheel lock and kill switch to help protect your vehicle from thieves.
Disarming the System
If you own a Ghost immobiliser that is fitted to your vehicle, it's vital to know how to disarm it. This will help you in the case that you lock your keys inside the car or when your battery dies. The system utilizes a unique PIN code that only you know. It cannot start the car without this code. Pressing a combination buttons on the steering wheel or dashboard is the simplest method to enter your code. This is much simpler than using a key fob and stops others from copying your remote.
Unlike some aftermarket immobilisers that require cutting wires to install, Ghost2 is non-invasive and is compatible with your vehicle's bus network to function. Its standout characteristic is its ability to bypass the engine without affecting your vehicle's normal functions, making it impossible for thieves to make use of signal boosters or duplicate your car key. It does not emit radio frequencies, which means thieves won't be able to detect it.
The Ghost system also comes with an option called Transport Mode that allows you to temporarily disable the security system in situations such as transportation or servicing. This is an excellent option if you want to lend your vehicle to someone else without sharing the PIN code or when you wish to secure your vehicle while driving it. To activate Transport Mode, press the service button five times within 2 seconds. The Ghost system will confirm activation with five indication signals.
Keep the emergency code inside your vehicle in a secure place. If you are ever locked out of your car You can call the company or technician who installed the system and they'll give you the code. If you cannot reach them then you can try to contact an authorized dealer but this would require verification procedures and could result in additional fees.
This system is not just useful, but it will also safeguard your vehicle from theft and reduce cost of insurance. Many insurance companies offer reduced monthly premiums, or even financial incentives for installing this anti-theft system.